PERHITUNGAN NILAI DAYA DUKUNG TIANG PANCANG BETON MENGGUNAKAN DATA SONDIR PADA PROYEK DERMAGA MESJID SULTAN SURIANSYAH

Dilla Novia, Risda Ratna (2023) PERHITUNGAN NILAI DAYA DUKUNG TIANG PANCANG BETON MENGGUNAKAN DATA SONDIR PADA PROYEK DERMAGA MESJID SULTAN SURIANSYAH. Diploma thesis, Universitas Islam Kalimantan MAB.

[img] Text
PENGESAHAN SKRIPSI RISDA.pdf

Download (327kB)
[img] Text
KEASLIAN SKRIPSI RISDA.pdf

Download (86kB)
[img] Text
ABSTRAK RISDA_removed.pdf

Download (108kB)

Abstract

Pondasi adalah bagian terendah dari bangunan-bangunan yang meneruskan beban bangunan ke tanah atau batuan yang ada dibawahnya. Pondasi tiang digunakan untuk mendukung bangunan yang menahan gaya angkat ke atas terutama pada bangunan-bangunan tingkat tinggi yang dipengaruhi oleh gaya-gaya penggulingan akibat beban angin. Selain itu, tiang-tiang juga digunakan untuk mendukung bangunan dermaga, di mana pada bangunan ini, tiang-tiang dipengaruhi oleh gaya-gaya benturan kapal dan gelombang air. Tujuan dari penelitian ini adalah untuk mengetahui nilai daya dukung tiang pancang berdasarkan data sondir dengan menggunakan metode Metode Schmertmann-Nottingham (1975) dan Metode Langsung (Direct Cone Method) untuk perhitungan daya dukung tiang pancangnya, sedangkan untuk menghitung efisiensi tiangnya menggunakan metode Conversi – Labarre dan Seiler Keeney. Hasil dari perhitungan daya dukung tiang tunggal menunjukan untuk Metode Schmertmann-Nottingham (1975 pada sondir titik 1 Qult = 241,86 ton dan sondir titik 2 Qult = 295,64 ton sedangkan Metode Langsung (Direct Cone Method) pada sondir titik 1 Qult = 372,77 ton dan sondir titik 2 Qult = 423,64 ton. Untuk perhitungan efisiensi pada metode Conversi – Labarre didapatkan hasil 0,90 dan metode Seiler Keeney didapatkan hasil 0,92. Kapasitas kelompok tiang menggunakan hasil daya dukung ultimit tiang tunggal dengan metode Schmertmann-Nottingham pada data sondir menggunakan 2 metode efisiensi didapat nilai untuk S1 sebesar 13060,44 ton, dan 13350,67 ton. Serta untuk S2 ialah sebesar 15964,56 ton, dan 16319,33 ton. Sedangkan hasil untuk kapasitas ijin kelompok tiang ialah sebesar 4353,48 ton. Kata Kunci : Sondir, Daya Dukung Tiang Pancang, Metode Schmertmann-Nottingham dan Metode Langsung (Direct Cone Method). ABSTRACT The foundation is the lowest part of the buildings that carry the burden of the building to the ground or rocks beneath it. Pile foundations are used to support buildings that resist uplift forces, especially in high-rise buildings that are affected by windmills. In addition, the masts are also used to support the pier building, where in this building, the masts are influenced by the force of ship collisions and water waves. The purpose of this study is to determine the carrying capacity of the pile based on sondir data using the Schmertmann-Nottingham Method (1975) and the Direct Cone Method for calculating the carrying capacity of the pole, while to calculate the efficiency of the pile using the Conversion - Labarre method and Seiler Keeney. The results of the calculation of the carrying capacity of a single pole show for the Schmertmann-Nottingham Method (1975) at sondir point 1 Qult = 241.86 tons and sondir point 2 Qult = 295.64 tons while the Direct Method (Direct Cone Method) at sondir point 1 Qult = 372 , 77 tons and sondir point 2 Qult = 423.64 tons For the calculation of efficiency in the Conversion-Labarre method the results were 0.90 and the Seiler Keeney method was obtained 0.92. The capacity of the pile group using the results of a single pole ultimit carrying capacity by the Schmertmann method -Nottingham on sondir data using 2 efficiency methods obtained values for S1 amounted to 13060.44 tons, and 13350.67 tons, and for S2 were 15964.56 tons and 16319.33 tons, while the yield for the permit capacity of the pile group was 4353.48 tons. Keywords : Sondir, Pile Bearing Capacity, Schmertmann-Nottingham Method dan Direct Method (Direct Cone Method).

Item Type: Thesis (Diploma)
Uncontrolled Keywords: Sondir, Daya Dukung Tiang Pancang, Metode Schmertmann-Nottingham dan Metode Langsung (Direct Cone Method). Sondir, Pile Bearing Capacity, Schmertmann-Nottingham Method dan Direct Method (Direct Cone Method).
Subjects: T Technology > TA Engineering (General). Civil engineering (General)
Depositing User: UPT PPJ
Date Deposited: 16 May 2023 02:10
Last Modified: 16 May 2023 02:10
URI: http://eprints.uniska-bjm.ac.id/id/eprint/16289

Actions (login required)

View Item View Item